In this tutorial, we’ll set up some BGP routers in Minikube, configure MetalLB to use them, and create some load-balanced services. We’ll be able to inspect the state of the BGP routers, and see that they reflect the intent that we expressed in Kubernetes.
Because this will be a simulated environment inside Minikube, this setup only lets you inspect the routers’s state and see what it would do in a real deployment. Once you’ve experimented in this setting and are ready to set up MetalLB on a real cluster, refer to the installation guide for instructions.
Here is the outline of what we’re going to do:
This tutorial currently only works on amd64 (aka x86_64) systems, because the test BGP router container image doesn’t work on other platforms yet.
If you don’t already have a Minikube cluster set up, follow
kubernetes.io to install Minikube and get your playground cluster
running. Once you’ve done so, you should be able to run
status and get output that looks something like this:
minikube: Running cluster: Running kubectl: Correctly Configured: pointing to minikube-vm at 192.168.99.100
You need to use Minikube >=0.24. Previous versions use a different IP range for cluster services, which is incompatible with the manifests used in this tutorial.
If you want to use Helm to install MetalLB, you need to install
minikube using the
kubeadm bootstrapper. The older
bootstrapper creates RBAC rules that are incompatible with Helm.
MetalLB exposes load-balanced services using the BGP routing protocol, so we need a BGP router to talk to. In a production cluster, this would be set up as a dedicated hardware router (e.g. an Ubiquiti EdgeRouter), or a soft router using open-source software (e.g. a Linux machine running the BIRD routing suite).
For this tutorial, we’ll deploy a pod inside minikube that runs both the BIRD and Quagga. They will be configured to speak BGP, but won’t configure Linux to forward traffic based on the data they receive. Instead, we’ll just inspect that data to see what a real router would do.
Deploy these test routers with
kubectl apply -f https://raw.githubusercontent.com/google/metallb/v0.6.2/manifests/test-bgp-router.yaml
This will create a deployment for our BGP routers, as well as four
cluster-internal services. Wait for the router pod to start, by
kubectl get pods -n metallb-system until you see the
test-bgp-router pod in the
NAME READY STATUS RESTARTS AGE test-bgp-router-57fb7c798f-xccv8 1/1 Running 0 3m
(your pod will have a slightly different name, because the suffix is randomly generated by the deployment – this is fine.)
In addition to the router pod, the
created four cluster-internal services:
test-bgp-router-birdservice exposes the BIRD BGP router at
10.96.0.100, so that we have a stable IP address for MetalLB to talk to.
test-bgp-router-quaggaservice exposes the Quagga router at
test-bgp-router-uiservice is a little UI that shows us what routers are thinking.
Let’s open that UI now. Run:
minikube service -n metallb-system
test-bgp-router-ui. This will open a new browser tab that should look
something like this:
If you’re comfortable with BGP and networking, the raw router status may be interesting. If you’re not, don’t worry, the important part is above: our routers are running, but know nothing about our Kubernetes cluster, because MetalLB is not connected.
Obviously, MetalLB isn’t connected to our routers, it’s not installed yet! Let’s address that. Keep the test-bgp-router-ui tab open, we’ll come back to it shortly.
MetalLB runs in two parts: a cluster-wide controller, and a per-machine BGP speaker. Since Minikube is a Kubernetes cluster with a single VM, we’ll end up with the controller and one BGP speaker.
Install MetalLB by applying the manifest:
kubectl apply -f https://raw.githubusercontent.com/google/metallb/v0.6.2/manifests/metallb.yaml
This manifest creates a bunch of resources. Most of them are related to access control, so that MetalLB can read and write the Kubernetes objects it needs to do its job.
Ignore those bits for now, the two pieces of interest are the
“controller” deployment, and the “speaker” daemonset. Wait for
these to start by monitoring
kubectl get pods -n
metallb-system. Eventually, you should see two running pods, in
addition to the BGP router from the previous step (again, the pod name
suffixes will be different on your cluster).
NAME READY STATUS RESTARTS AGE speaker-5x8rf 1/1 Running 0 2m controller-65c85447-8tngv 1/1 Running 0 3m test-bgp-router-57fb7c798f-xccv8 1/1 Running 0 3m
Refresh the test-bgp-router-ui tab from earlier, and… It’s the same! MetalLB is still not connected, and our routers still know nothing about cluster services.
That’s because the MetalLB installation manifest doesn’t come with a configuration, so both the controller and BGP speaker are sitting idle, waiting to be told what they should do. Let’s fix that!
We have a sample MetalLB configuration in
manifests/tutorial-1.yaml. Let’s take a look at it before applying
apiVersion: v1 kind: ConfigMap metadata: namespace: metallb-system name: config data: config: | peers: - my-asn: 64500 peer-asn: 64500 peer-address: 10.96.0.100 - my-asn: 64500 peer-asn: 64500 peer-address: 10.96.0.101 address-pools: - name: my-ip-space protocol: bgp addresses: - 198.51.100.0/24
MetalLB’s configuration is a standard Kubernetes ConfigMap,
config under the
metallb-system namespace. It contains two
pieces of information: who MetalLB should talk to, and what IP
addresses it’s allowed to hand out.
In this configuration, we’re setting up a BGP peering with
10.96.0.102, which are the addresses
respectively. And we’re giving MetalLB 256 IP addresses to use, from
198.51.100.0 to 198.51.100.255. The final section gives MetalLB some
BGP attributes that it should use when announcing IP addresses to our
Apply this configuration now:
kubectl apply -f https://raw.githubusercontent.com/google/metallb/v0.6.2/manifests/tutorial-1.yaml
The configuration should take effect within a few seconds. Refresh the
test-bgp-router-ui browser page again (run
minikube service -n
metallb-system test-bgp-router-ui if you closed it and need to get it
back). If all went well, you should see happier routers:
Success! The MetalLB BGP speaker connected to our routers. You can
verify this by looking at the logs for the BGP speaker. Run
logs -n metallb-system -l app=speaker, and among other log
entries, you should find something like:
I1127 08:53:49.118588 1 main.go:203] Start config update I1127 08:53:49.118705 1 main.go:255] Peer "10.96.0.100" configured, starting BGP session I1127 08:53:49.118710 1 main.go:255] Peer "10.96.0.101" configured, starting BGP session I1127 08:53:49.118729 1 main.go:270] End config update I1127 08:53:49.170535 1 bgp.go:55] BGP session to "10.96.0.100:179" established I1127 08:53:49.170932 1 bgp.go:55] BGP session to "10.96.0.101:179" established
However, as the BGP routers pointed out, MetalLB is connected, but isn’t telling them about any services yet. That’s because all the services we’ve defined so far are internal to the cluster. Let’s change that!
manifests/tutorial-2.yaml contains a trivial service: an nginx pod,
and a load-balancer service pointing at nginx. Deploy it to the cluster now:
kubectl apply -f https://raw.githubusercontent.com/google/metallb/v0.6.2/manifests/tutorial-2.yaml
Again, wait for nginx to start by monitoring
kubectl get pods, until
you see a running nginx pod. It should look something like this:
NAME READY STATUS RESTARTS AGE nginx-558d677d68-j9x9x 1/1 Running 0 47s
Once it’s running, take a look at the
nginx service with
kubectl get service nginx:
NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE nginx LoadBalancer 10.96.0.29 198.51.100.0 80:32732/TCP 1m
We have an external IP! Because the service is of type LoadBalancer,
198.51.100.0 from the address pool we configured, and
assigned it to the nginx service. You can see this even more clearly
by looking at the event history for the service, with
describe service nginx:
Type Reason Age From Message ---- ------ ---- ---- ------- Normal IPAllocated 24m metallb-controller Assigned IP "198.51.100.0"
Refresh your test-bgp-router-ui page, and see what our routers thinks:
Success! MetalLB told our routers that 198.51.100.0 exists on our Minikube VM, and that the routers should forward any traffic for that IP to us.
In the previous step, MetalLB assigned the address 198.51.100.0, the
first address in the pool we gave it. That IP address is perfectly
valid, but some old and buggy wifi routers mistakenly think it isn’t,
because it ends in
As it turns out, one of our customers called and complained of this
exact problem. Fortunately, MetalLB has a configuration option to
address this. Take a look at the configuration in
apiVersion: v1 kind: ConfigMap metadata: namespace: metallb-system name: config data: config: | peers: - my-asn: 64500 peer-asn: 64500 peer-address: 10.96.0.100 - my-asn: 64500 peer-asn: 64500 peer-address: 10.96.0.101 address-pools: - name: my-ip-space protocol: bgp avoid-buggy-ips: true addresses: - 198.51.100.0/24
There’s just one change compared to our previous configuration: in the
address pool configuration, we added
avoid-buggy-ips: true. This
tells MetalLB that IP addresses ending in
.255 should not be
Sounds easy enough, let’s apply that configuration:
kubectl apply -f https://raw.githubusercontent.com/google/metallb/v0.6.2/manifests/tutorial-3.yaml
Refresh the test-bgp-router-ui page and… Hmm, strange, our routers
are still being told to use
198.51.100.0, even though we just told
MetalLB that this address should not be used. What happened?
To answer that, let’s inspect the running configuration in Kubernetes,
kubectl describe configmap -n metallb-system
config. At the bottom of the output, you should see an event
log that looks like this:
Events: Type Reason Age From Message ---- ------ ---- ---- ------- Warning InvalidConfig 29s metallb-controller configuration rejected: new config not compatible with assigned IPs: service "default/nginx" cannot own "198.51.100.0" under new config Warning InvalidConfig 29s metallb-speaker configuration rejected: new config not compatible with assigned IPs: service "default/nginx" cannot own "198.51.100.0" under new config
Oops! Both the controller and the BGP speaker rejected our new configuration, because it would break an already existing service. This illustrates an important policy that MetalLB tries to follow: applying new configurations should not break existing services.
(You might ask why we were able to apply an invalid configuration at all. Good question! This is a missing feature of MetalLB. In future, MetalLB will validate new configurations when they are submitted by kubectl, and make Kubernetes refuse unsafe configurations. But for now, it will merely complain after the fact, and ignore the new configuration.)
At this point, MetalLB is still running on the previous configuration, the one that allows nginx to use the IP it currently has. If this were a production cluster with Prometheus monitoring, we would be getting an alert now, warning us that the configmap written to the cluster is not compatible with the cluster’s running state.
Okay, so how do we fix this? We need to explicitly change the
configuration of the nginx service to be compatible with the new
configuration. To do this, run
kubectl edit service nginx, and in
spec section add:
Save the change, and run
kubectl describe service nginx again. You
should see an
IPAllocated event showing that MetalLB changed the
service’s assigned address as instructed.
Now, the new configuration that we tried to apply is valid, because
nothing is using the
.0 address any more. Let’s reapply it, so that
MetalLB reloads again:
kubectl apply -f https://raw.githubusercontent.com/google/metallb/v0.6.2/manifests/tutorial-4.yaml
You may have noticed that we applied tutorial-4.yaml, not the tutorial-3.yaml from before. This is another rough edge in the current version of MetalLB: when we submitted the configuration in tutorial-3.yaml, MetalLB looked at it and rejected it, but will not look at it again to see if it has become valid. To make MetalLB examine the configuration again, we need to make some cosmetic change to the config, so that Kubernetes notifies MetalLB that there is a new configuration to load. tutorial-4.yaml just adds a no-op comment to the configuration to make Kubernetes signal MetalLB.
This piece of clunkiness will also go away when MetalLB learns to validate new configurations before accepting the submission from kubectl.
This time, MetalLB accepts the new configuration, and everything is
happy once again. And, refreshing test-bgp-router-ui, we see that the
routers did indeed see the change from
One final bit of clunkiness: right now, you need to inspect metallb’s logs to see that a new configuration was successfully loaded. Once MetalLB only allows valid configurations to be submitted, this clunkiness will also go away.
If you’re not using the minikube cluster for anything else, you can
clean up simply by running
minikube delete. If you want to do a more
targeted cleanup, you can delete just the things we created in this
kubectl delete -f https://raw.githubusercontent.com/google/metallb/v0.6.2/manifests/tutorial-2.yaml,https://raw.githubusercontent.com/google/metallb/v0.6.2/manifests/test-bgp-router.yaml,https://raw.githubusercontent.com/google/metallb/v0.6.2/manifests/metallb.yaml
This will tear down all of MetalLB, as well as our test BGP routers and the nginx load-balanced service.